| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246 |
- /* Intel Cherryview/VLV display PWM panel backlight.
- *
- * Braswell/Cherryview (and Bay Trail/Valleyview) drive the internal panel
- * backlight from the display engine, not from the Chrome EC. The VBT
- * (block 43, LFP backlight) on google/setzer selects PWM controller 0 at
- * 200 Hz, active high. Linux drives the same registers from i915
- * (vlv_setup_backlight()/vlv_set_backlight()):
- *
- * BLC_PWM_CTL2 pipe A VLV_DISPLAY_BASE + 0x61250 (0x1E1250)
- * BLC_PWM_CTL pipe A VLV_DISPLAY_BASE + 0x61254 (0x1E1254)
- * pipe B adds 0x100.
- *
- * BLC_PWM_CTL2 bit 31 enables the PWM, bit 28 is the polarity.
- * BLC_PWM_CTL bits 31:16 are the period and bits 15:0 the duty cycle.
- *
- * The PWM clock is 19.2 MHz with a fixed /16 increment on Cherryview, so
- * 200 Hz is a period of 6000. At probe time the period the firmware left
- * in the register wins; 6000 is only the fallback when it reads as zero.
- */
- #include "backlight.h"
- #include "paging.h"
- #include "pci.h"
- #include "serial.h"
- #define INTEL_CHV_GFX_B0 0x22b0
- #define INTEL_CHV_GFX_C0 0x22b1
- #define VLV_DISPLAY_BASE 0x180000u
- #define VLV_BLC_PWM_CTL2(pipe) (VLV_DISPLAY_BASE + 0x61250u + \
- ((pipe) ? 0x100u : 0u))
- #define VLV_BLC_PWM_CTL(pipe) (VLV_DISPLAY_BASE + 0x61254u + \
- ((pipe) ? 0x100u : 0u))
- #define BLM_PWM_ENABLE (1u << 31)
- #define BLC_DUTY_MASK 0xFFFFu
- #define BLC_MIN_PERCENT 5
- #define BLC_STEP_PERCENT 10
- #define BLC_DEFAULT_PERIOD 6000u /* 19.2 MHz / (200 Hz * 16) */
- static unsigned int blc_bar; /* physical BAR (reported) */
- static unsigned int blc_regs; /* its kernel mapping */
- static unsigned int blc_pipe;
- static unsigned int blc_period;
- static unsigned int blc_duty;
- static int blc_level;
- static int blc_present;
- static int blc_enabled;
- static unsigned int blc_seq; /* bumped on every user-visible change */
- static unsigned int blc_read(unsigned int reg)
- {
- return *(volatile unsigned int *)(blc_regs + reg);
- }
- static void blc_write(unsigned int reg, unsigned int val)
- {
- *(volatile unsigned int *)(blc_regs + reg) = val;
- }
- void backlight_init(unsigned int bus, unsigned int dev, unsigned int device_id)
- {
- unsigned int bar0, ctl2[2], ctl[2], period, duty, i;
- int pipe, a_ok, b_ok;
- blc_bar = 0;
- blc_pipe = 0;
- blc_period = 0;
- blc_duty = 0;
- blc_level = 0;
- blc_present = 0;
- blc_enabled = 0;
- if (device_id != INTEL_CHV_GFX_B0 && device_id != INTEL_CHV_GFX_C0)
- return;
- bar0 = pci_cfg_read32(bus, dev, 0, 0x10);
- if (bar0 & 1)
- return; /* I/O BAR, not MMIO */
- if (!(bar0 & 0xFFFFFFF0u))
- return;
- if ((bar0 & 0x6) == 0x4 &&
- pci_cfg_read32(bus, dev, 0, 0x14) != 0)
- return; /* 64-bit BAR above 4 GB */
- /* The backlight registers live below 2 MB in the display MMIO BAR. */
- blc_bar = bar0 & 0xFFFFFFF0u;
- blc_regs = (unsigned int)ioremap(blc_bar, 0x200000, IOREMAP_MMIO);
- if (!blc_regs) {
- blc_bar = 0;
- return;
- }
- for (i = 0; i < 2; i++) {
- ctl2[i] = blc_read(VLV_BLC_PWM_CTL2(i));
- ctl[i] = blc_read(VLV_BLC_PWM_CTL(i));
- }
- a_ok = !(ctl2[0] == 0xFFFFFFFFu && ctl[0] == 0xFFFFFFFFu);
- b_ok = !(ctl2[1] == 0xFFFFFFFFu && ctl[1] == 0xFFFFFFFFu);
- if (!a_ok && !b_ok) {
- serial_puts(SERIAL_COM1, "backlight: no display MMIO\n");
- return;
- }
- /* Follow the pipe the firmware enabled; when both or neither are
- * enabled, use the active display plane; otherwise fall back to the
- * VBT's controller 0 (pipe A). The internal panel is normally on A. */
- pipe = 0;
- if (!a_ok) {
- pipe = 1;
- } else if (b_ok &&
- (ctl2[0] & BLM_PWM_ENABLE) == (ctl2[1] & BLM_PWM_ENABLE)) {
- unsigned int dspa = blc_read(VLV_DISPLAY_BASE + 0x70180);
- unsigned int dspb = blc_read(VLV_DISPLAY_BASE + 0x71180);
- if (!(dspa & (1u << 31)) && (dspb & (1u << 31)))
- pipe = 1;
- } else if (b_ok && (ctl2[1] & BLM_PWM_ENABLE)) {
- pipe = 1;
- }
- period = ctl[pipe] >> 16;
- if (!period)
- period = BLC_DEFAULT_PERIOD;
- duty = ctl[pipe] & BLC_DUTY_MASK;
- if (duty > period)
- duty = period;
- blc_pipe = (unsigned int)pipe;
- blc_period = period;
- blc_duty = duty;
- blc_level = (int)((duty * 100u + period / 2u) / period);
- if (blc_level > 100)
- blc_level = 100;
- if (blc_level < BLC_MIN_PERCENT)
- blc_level = BLC_MIN_PERCENT;
- blc_enabled = (ctl2[pipe] & BLM_PWM_ENABLE) != 0;
- blc_present = 1;
- serial_puts(SERIAL_COM1, "backlight: CHV PWM pipe ");
- serial_puts(SERIAL_COM1, pipe ? "B" : "A");
- serial_puts(SERIAL_COM1, ", period ");
- serial_putdec(SERIAL_COM1, period);
- serial_puts(SERIAL_COM1, ", duty ");
- serial_putdec(SERIAL_COM1, duty);
- serial_puts(SERIAL_COM1, " (");
- serial_putdec(SERIAL_COM1, (unsigned int)blc_level);
- serial_puts(SERIAL_COM1, "%), ");
- serial_puts(SERIAL_COM1, blc_enabled ? "enabled" : "disabled");
- serial_puts(SERIAL_COM1, ", ctl2 ");
- serial_puthex(SERIAL_COM1, ctl2[0]);
- serial_puthex(SERIAL_COM1, ctl2[1]);
- serial_puts(SERIAL_COM1, ", ctl ");
- serial_puthex(SERIAL_COM1, ctl[0]);
- serial_puthex(SERIAL_COM1, ctl[1]);
- serial_puts(SERIAL_COM1, "\n");
- }
- int backlight_present(void)
- {
- return blc_present;
- }
- int backlight_percent(void)
- {
- return blc_present ? blc_level : -1;
- }
- unsigned int backlight_seq(void)
- {
- return blc_seq;
- }
- void backlight_set_percent(int percent)
- {
- unsigned int ctl2, duty;
- if (!blc_present)
- return;
- if (percent < BLC_MIN_PERCENT)
- percent = BLC_MIN_PERCENT;
- if (percent > 100)
- percent = 100;
- blc_seq++;
- duty = (blc_period * (unsigned int)percent + 50u) / 100u;
- if (duty > blc_period)
- duty = blc_period;
- if (percent && !duty)
- duty = 1;
- if (!blc_enabled) {
- ctl2 = blc_read(VLV_BLC_PWM_CTL2(blc_pipe));
- blc_write(VLV_BLC_PWM_CTL2(blc_pipe), ctl2 & ~BLM_PWM_ENABLE);
- blc_write(VLV_BLC_PWM_CTL(blc_pipe),
- (blc_period << 16) | duty);
- (void)blc_read(VLV_BLC_PWM_CTL(blc_pipe));
- blc_write(VLV_BLC_PWM_CTL2(blc_pipe),
- (ctl2 & ~BLM_PWM_ENABLE) | BLM_PWM_ENABLE);
- (void)blc_read(VLV_BLC_PWM_CTL2(blc_pipe));
- blc_enabled = 1;
- } else {
- blc_write(VLV_BLC_PWM_CTL(blc_pipe),
- (blc_period << 16) | duty);
- (void)blc_read(VLV_BLC_PWM_CTL(blc_pipe));
- }
- blc_duty = duty;
- blc_level = percent;
- }
- void backlight_step(int dir)
- {
- int level;
- if (!blc_present)
- return;
- level = blc_level + (dir > 0 ? BLC_STEP_PERCENT : -BLC_STEP_PERCENT);
- backlight_set_percent(level);
- }
- int backlight_status(struct backlight_status *out)
- {
- unsigned int i;
- if (!out)
- return -1;
- for (i = 0; i < sizeof(*out); i++)
- ((unsigned char *)out)[i] = 0;
- out->present = blc_present;
- if (!blc_present)
- return -1;
- out->level = blc_level;
- out->enabled = blc_enabled;
- out->pipe = blc_pipe;
- out->period = blc_period;
- out->duty = blc_duty;
- out->bar = blc_bar;
- /* Keep the two pipe snapshots live for the `backlight probe` dump. */
- out->ctl2[0] = blc_read(VLV_BLC_PWM_CTL2(0));
- out->ctl2[1] = blc_read(VLV_BLC_PWM_CTL2(1));
- out->ctl[0] = blc_read(VLV_BLC_PWM_CTL(0));
- out->ctl[1] = blc_read(VLV_BLC_PWM_CTL(1));
- return 0;
- }
|